Top 10 typical forklift mishaps ， forklift procedure must focus on these matters ！.

Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is steady and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal ought to be released initially. High-speed sharp turns are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to obey the traffic rules in the factory and should keep a certain security distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest position that does not impede the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when piling or filling. .
8. The elevation of the lots need to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt way, and they will never ever operate with diseases or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique circumstances, safety and security warning signs have Electric Forklift Truck for Warehouse to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the load, and it must be kept in mind that the fork suggestion must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Straining is banned, and it is restricted to utilize forks to raise workers to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or dispirit the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go Stand-on Electric Pallet Stacker beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak must also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to avoid the tendency of " cost-free turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not allowed under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844